※全手順・表示を洩らさず(バイナリイメージ展開の表示は除く)連続で１ページに記載しました！！
(8)-a) と同様、HDDの概略マップを作成しました。
色分け： 黒：画面表示 赤：入力 青：コメント
/* さあ、それではスイッチON！ */
U-Boot 1.1.4 LiSt 2.1.0 (Sep 21 2006 - 00:22:56) LinkStation / KuroBox
--- (8)Debian5.0(lenny)のインストール ---
b-1) U-Boot を用いてlennyをインストール
※全手順・表示を洩らさず(バイナリイメージ展開の表示は除く)連続で１ページに記載しました！！
(8)-a) と同様、HDDの概略マップを作成しました。
色分け： 黒：画面表示 赤：入力 青：コメント
/* さあ、それではスイッチON！ */
U-Boot 1.1.4 LiSt 2.1.0 (Sep 21 2006 - 00:22:56) LinkStation / KuroBox
CPU: MPC8245 Revision 1.4 at 196.608 MHz: 16 kB I-Cache 16 kB D-Cache
DRAM: 64 MB
FLASH: 4 MB
*** Warning - bad CRC, using default environment
00 0b 1317 0985 0200 ff
00 0c 1095 0680 0101 ff
00 0e 1033 0035 0c03 ff
00 0e 1033 0035 0c03 ff
00 0e 1033 00e0 0c03 ff
Net: COMET#0
next_cons_choice: Unexpected code: 0x33
stdin : serial
stdout: serial
stderr: serial
IDE: Bus 0: OK
Device 0: Model: TS8GSSD25-S Firm: Ser#: 00000142
Type: Hard Disk
Capacity: 7775.5 MB = 7.5 GB (15924384 x 512)
Boot in 02 seconds ('s' to stop).. /* [s]キーでU-Bootのコマンドモード */
=> run writeng /* EMモードに入るためのコマンド */
Un-Protected 1 sectors
Flash erase: first = 55 @ 0xfff70000
last = 55 @ 0xfff70000
Flash erase: Done
Erased 1 sectors
Copy to Flash... done
=> run emboot /* EMモード起動 */
## Booting image at ffc00000 ...
******* Product Information *******
----------------------------------
Product Name: KURO-BOX(IETSUNA)
VER: 1.02
Date: 2004/4/16 11:46:41
----------------------------------
Verifying checksum... OK
Uncompressing kernel...done.
Loading Ramdisk at 0x03C67000, end 0x03E6E647 ... OK
Booting the kernel
Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.17_kuro-box (root@toda_dev.melcoinc.co.jp) (gcc version 2.95.3 20010315 (release/MontaVista)) #4 2004? 4ｷ・16ﾆ・ｶ簣ﾋﾆ・11:45:05 JST
KURO-BOX (C) 2004 KUROUTO-SHIKOU.
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda1
OpenPIC Version 1.2 (1 CPUs and 139 IRQ sources) at 80040000
decrementer frequency = 24.378523 MHz
rtc sec count 1296565257
Calibrating delay loop... 129.84 BogoMIPS
Memory: 60532k available (1124k kernel code, 520k data, 188k init, 0k highmem)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
BUFFALO INC. RTC driver ver 1.00
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x80004600 (irq = 138) is a 16550A
ttyS01 at 0x80004500 (irq = 137) is a 16550A
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 10000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CMD680: IDE controller on PCI bus 00 dev 60
CMD680: chipset revision 2
CMD680: 100% native mode on irq 17
ide0: BM-DMA at 0xbffed0-0xbffed7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xbffed8-0xbffedf, BIOS settings: hdc:pio, hdd:pio
hda: TS8GSSD25-S, ATA DISK drive
ide0 at 0xbffef8-0xbffeff,0xbffef6 on irq 17
hda: 15924384 sectors (8153 MB) w/1KiB Cache, CHS=15798/16/63, UDMA(66)
Partition check:
hda: hda1 hda2 hda3 hda4
loop: loaded (max 8 devices)
FLASHDISK:Initialized [FUJITSU MBM29PL32TM]
Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
tulip0: MII transceiver #1 config 3100 status 7849 advertising 05e1.
eth0: ADMtek Comet rev 17 at 0xbfff00, 00:0D:0B:87:5C:5F, IRQ 16.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: AppleTalk 0.18a for Linux NET4.0
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 2077k freed
Boot from initrd.
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Boot from initrd.
VFS: Mounted root (ext2 filesystem).
change_root: old root has d_count=5
Trying to unmount old root ... <3>error -16
Change root to /initrd: error -2
Freeing unused kernel memory: 188k init
kmod: failed to exec /sbin/modprobe -s -k char-major-4, errno = 2
INIT: version 2.78 booting
[: 0: unexpected operator
Mounting local filesystems...
none on /dev/pts type devpts (rw,gid=5,mode=20)
Cleaning: /tmp .
Configuration network interface: lo eth0
dhcpcd[37]: infinite IP address lease time. Exiting
Starting system log daemon: syslogd klogd.
INIT: Entering runlevel: 2
Starting AP serv daemon:AP serv starting on eth0
Starting internet superserver: inetd.
Start services: ppc_uartd
Kroutoshikou KURO-BOX (IETSUNA)
kernel 2.4.17-kuro-box on ppc
KURO-BOX-EM login: root /* EMモードに root でログイン */
Password: /* 出荷時パスワードは「kuro」 */
#
/* --------------------------------------------------------------------- */
次にHDDを初期化、領域分割、フォーマットを行います。
使用するコマンドは「/sbin/mfdisk」と「/sbin/mke2fs」
使用HDDはTrancsendのSSD TS8GSSD25-S(8GB)
領域分割は以下の通り
hda1：４GB debian5.0(lenny, kernel 2.6.20)
hda2：256MB SWAP領域
hda3：残り、データ保存用
/* --------------------------------------------------------------------- */
#
# /sbin/mfdisk -e /dev/hda /* HDD全領域を削除 */
delete partition 1
delete partition 2
delete partition 3
delete partition 4
create partitions...
deleate all partitions.
The partition table has been altered!
Syncing disks.
#
# /sbin/mfdisk -c /dev/hda /* 続いて領域確保(以下、対話形式です) */
Command (m for help): n /* 第1領域を４GB確保 */
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-15798, default 1):[入力なしでenter]
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-15798, default 15798): +4000M
Command (m for help): n /* 第2領域を256MB確保 */
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (8128-15798, default 8128):[入力なしでenter]
Using default value 8128
Last cylinder or +size or +sizeM or +sizeK (8128-15798, default 15798): +256M
Command (m for help): n /* 第3領域は残り全部 */
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 3
First cylinder (8649-15798, default 8649):[入力なしでenter]
Using default value 8649
Last cylinder or +size or +sizeM or +sizeK (8649-15798, default 15798):[入力なしでenter]
Using default value 15798
Command (m for help): t /* 第2領域をSWAP用に予約(82番) */
Partition number (1-4): 2
Hex code (type L to list codes): 82
Changed system type of partition 2 to 82 (Linux swap)
Command (m for help): p /* 結果の一覧を表示 */
Disk /dev/hda: 16 heads, 63 sectors, 15798 cylinders
Units = cylinders of 1008 * 512 bytes
Device Boot Start End Blocks Id System
/dev/hda1 1 8127 4095976+ 83 Linux
/dev/hda2 8128 8648 262584 82 Linux swap
/dev/hda3 8649 15798 3603600 83 Linux
Command (m for help): w /* 最後に分割結果をHDDに書込み */
The partition table has been altered!
Syncing disks.
#
# /sbin/mke2fs -j /dev/hda1 /* 第1領域をフォーマット(Linux用) */
mke2fs 1.22, 22-Jun-2001 for EXT2 FS 0.5b, 95/08/09
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
512000 inodes, 1023994 blocks
51199 blocks (5.00%) reserved for the super user
First data block=0
32 block groups
32768 blocks per group, 32768 fragments per group
16000 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736
Writing inode tables: done
Creating journal (8192 blocks): done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 21 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
#
# /sbin/mkswap /dev/hda2 /* 第2領域をSWAPに設定 */
Setting up swapspace version 1, size = 268881920 bytes
#
# /sbin/mke2fs -j -m 0 /dev/hda3 /* 第3領域をフォーマット(予約なし) */
mke2fs 1.22, 22-Jun-2001 for EXT2 FS 0.5b, 95/08/09
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
450688 inodes, 900900 blocks
0 blocks (0.00%) reserved for the super user
First data block=0
28 block groups
32768 blocks per group, 32768 fragments per group
16096 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736
Writing inode tables: done
Creating journal (8192 blocks): done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 28 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
#
# /sbin/tune2fs -m 0 /dev/hda3 /* 念の為もう一度hda3を予約なしに設定 */
tune2fs 1.22, 22-Jun-2001 for EXT2 FS 0.5b, 95/08/09
Setting reserved blocks percentage to 0 (0 blocks)
#
/* ------------------------------------------------------------------------- */
/* 次にマウント */
#
# mount -t ext3 /dev/hda1 /mnt
# mount -t ext3 /dev/hda3 /mnt2
#
# df -h
Filesystem Size Used Available Use% Mounted on
/dev/ram0 9.5M 5.0M 4.5M 53% /
/dev/hda1 3.8G 32.1M 3.6G 1% /mnt
/dev/hda3 3.4G 32.1M 3.4G 1% /mnt2
#
/* -------------------------------------------------------------------------
続いてデータ領域(hda3)に必要なデータをFTPでコピー
FTPクライアントはWindowsXPマシンで
フリーソフト「FFFTP ver.1.97a」を使用
http://www2.biglobe.ne.jp/~sota/ffftp.html
使用するファイルは /dev/hda3 に /u-bootディレクトリを作製して保存
Revulo's Laboratoryより debian5.0 lenny の圧縮ファイル
http://cid-a95b9af71540ba41.skydrive.live.com/self.aspx/.Public/kuro-box/debian-lenny-kuroBOX-20090317.tgz
ちなみにこのファイル、アドレスの最後がファイル名なのでアクセスすればすぐに
ダウンロードを開始しそうですが、画面が変わるだけです。以下の画像に示すように
赤丸で囲んだ画像をクリックするとダウンロードを開始します。
 |
genbako.com様のサイトよりカーネルイメージとカーネルモジュール
http://www.genbako.com/uImage/kernelimage-2.6.20-kuroBOX-uImage.tgz
http://www.genbako.com/modules-2.6.20-kuroBOX.tgz
/* ------------------------------------------------------------------------- */
/* データの転送が済んだら確認 */
#
# ls /mnt2/u-boot /* /dev/hda3 は /mnt にマウントしてある */
debian-lenny-kuroBOX-20090317.tgz
kernelimage-2.6.20-kuroBOX-uImage.tgz
modules-2.6.20-kuroBOX.tgz
#
------------------------------------------------------------------------- */
Debian5.0(lenny)を hda1(マウントポイントは /mnt)に展開
------------------------------------------------------------------------- */
# cd /mnt
# pwd
/mnt
# tar xvzf /mnt2/u-boot/debian-lenny-kuroBOX-20090317.tgz
・
・
展開されたファイルがズラズラ表示される
・
・
#
/* hda1(/mnt)の確認 */
# ls /mnt
bin home mnt sbin tmp
boot lib opt selinux usr
dev lost+found proc srv var
etc media root sys
#
/* -------------------------------------------------------------------------
カーネルイメージ(2.6.20)を /boot に展開
------------------------------------------------------------------------- */
# tar xvfz /mnt2/u-boot/kernelimage-2.6.20-kuroBOX-uImage.tgz
.config
System.map
vmlinux.UBoot
uImage
#
# ls /mnt/boot /* /boot の内容を確認 */
System.map uImage vmlinux.UBoot
#
/* -------------------------------------------------------------------------
/mnt/lib/modules (/dev/hda1 の /lib/modules)にカーネルモジュールを展開
------------------------------------------------------------------------- */
# cd /mnt/lib/modules
# pwd
/mnt/lib/modules
# tar xvzf /mnt2/u-boot/modules-2.6.20-kuroBOX.tgz
・
・
展開されたファイルがズラズラ表示される
・
・
# ls
2.6.20-kurobox /* /lib/modules/2.6.20-kuroboxが出来ている */
# ls 2.6.20-kurobox /* 2.6.20-kuroboxディレクトリの内容を確認 */
build modules.dep modules.pcimap
kernel modules.ieee1394map modules.symbols
modules.alias modules.inputmap modules.usbmap
modules.ccwmap modules.isapnpmap source
#
/* -------------------------------------------------------------------------
再起動の前に lenny のネットワーク設定を使用環境に合わせておく
------------------------------------------------------------------------- */
# vi /mnt/etc/network/interfaces
#
# cat /mnt/etc/network/interfaces
# Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
# /usr/share/doc/ifupdown/examples for more information.
iface eth0 inet static
address 192.168.0.58
network 192.168.0.0
netmask 255.255.255.0
broadcast 192.168.0.255
gateway 192.168.0.1
iface lo inet loopback
auto eth0 lo
#
# vi /mnt/etc/hosts
#
# cat /mnt/etc/hosts
127.0.0.1 localhost
192.168.0.58 KURO-BOX
# The following lines are desirable for IPv6 capable hosts
# (added automatically by netbase upgrade)
#::1 ip6-localhost ip6-loopback
#fe00::0 ip6-localnet
#ff00::0 ip6-mcastprefix
#ff02::1 ip6-allnodes
#ff02::2 ip6-allrouters
#ff02::3 ip6-allhosts
#
# vi /mnt/etc/hosts.allow
#
# cat /mnt/etc/hosts.allow
# /etc/hosts.allow: list of hosts that are allowed to access the system.
# See the manual pages hosts_access(5), hosts_options(5)
# and /usr/doc/netbase/portmapper.txt.gz
#
# Example: ALL: LOCAL @some_netgroup
# ALL: .foobar.edu EXCEPT terminalserver.foobar.edu
#
# If you're going to protect the portmapper use the name "portmap" for the
# daemon name. Remember that you can only use the keyword "ALL" and IP
# addresses (NOT host or domain names) for the portmapper, as well as for
# rpc.mountd (the NFS mount daemon). See portmap(8), rpc.mountd(8) and
# /usr/share/doc/portmap/portmapper.txt.gz for further information.
#
#ALL: 192.168.0.0/255.255.0.0
#ALL: 127.0.0.1
ALL : ALL : ALLOW
#
#
# vi /mnt/etc/resolv.conf
#
# cat /mnt/etc/resolv.conf
search
nameserver 192.168.0.1
#
/* -------------------------------------------------------------------------
これで作業終了！ 再起動します
------------------------------------------------------------------------- */
# echo -n 'OKOK' > /dev/fl3 /* EMモードを抜けるためのコマンド */
#
# dd if=/dev/fl3 bs=2 count=2 /* /dev/fl3に 'OKOK' が書けたか確認 */
OKOK2+0 records in
2+0 records out
#
# reboot
INIT: Switching to runlevel: 6
Broadcast message from root (console) Wed Feb 2 06:38:40 2011...
The system is going down for reboot NOW !!
INIT: Sending processes the TERM signal
INIT: Sending processeStopping internet superserver: inetd.
Stop services: ppc_uartdStopping system log daemon: klogd syslogd.
Stop services: ppc_uartd
Sending all processes the TERM signal... Exiting Syslogd!
done.
Sending all processes the KILL signal... done.
Unmounting remote filesystems... done.
Deactivating swap... swapoff: not found
done.
Unmounting local filesystems... done.
Rebooting... flushing ide devices: hda
Restarting system.
/* -------------------------------------------------------------------------
ここまでが EMモード、以下 U-Boot の起動 〜 debian5.0(lenny)の起動
------------------------------------------------------------------------- */
U-Boot 1.1.4 LiSt 2.1.0 (Sep 21 2006 - 00:22:56) LinkStation / KuroBox
CPU: MPC8245 Revision 1.4 at 196.608 MHz: 16 kB I-Cache 16 kB D-Cache
DRAM: 64 MB
FLASH: 4 MB
*** Warning - bad CRC, using default environment
00 0b 1317 0985 0200 ff
00 0c 1095 0680 0101 ff
00 0e 1033 0035 0c03 ff
00 0e 1033 0035 0c03 ff
00 0e 1033 00e0 0c03 ff
Net: COMET#0
next_cons_choice: Unexpected code: 0x33
stdin : serial
stdout: serial
stderr: serial
IDE: Bus 0: OK
Device 0: Model: TS8GSSD25-S Firm: Ser#: 00000142
Type: Hard Disk
Capacity: 7775.5 MB = 7.5 GB (15924384 x 512)
Boot in 01 seconds ('s' to stop)...
Loading 0:1:boot/vmlinux.UBoot
1327058 bytes read
## Booting image at 00800000 ...
Image Name: Linux-2.6.20-kurobox
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1326994 Bytes = 1.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
KERNELBASE=c0000000 (r6=7fff00 r7=7fff0e) r3=7ffec0 (r4=0 r5=0)
Linux version 2.6.20-kurobox (hiroyuki@hg-lan) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #2 Mon Feb 5 23:11:01 JST 2007
Early serial console at MMIO 0x80004600 (options '57600n8')
BUFFALO Network Attached Storage Series
(C) 2002-2005 BUFFALO INC.
Zone PFN ranges:
DMA 0 -> 16384
Normal 16384 -> 16384
early_node_map[1] active PFN ranges
0: 0 -> 16384
Built 1 zonelists. Total pages: 16256
Kernel command line: root=/dev/hda1
OpenPIC Version 1.2 (1 CPUs and 11 IRQ sources) at 80040000
PID hash table entries: 256 (order: 8, 1024 bytes)
decrementer frequency = 24.391680 MHz
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62116k available (1932k kernel code, 740k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
I2C: rs5c372 RTC driver successfully loaded
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x80004600 (irq = 26) is a 16550A
serial8250.1: ttyS1 at MMIO 0x80004500 (irq = 25) is a 16550A
RAMDISK driver initialized: 2 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Linux Tulip driver version 1.1.14 (May 11, 2002)
tulip0: MII transceiver #1 config 1000 status 786d advertising 05e1.
eth0: ADMtek Comet rev 17 at Port 0xbfff00, 00:0D:0B:87:5C:5F, IRQ 16.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SiI680: IDE controller at PCI slot 0000:00:0c.0
SiI680: chipset revision 2
siimage: IDE controller MMIO ports not available.
SiI680: BASE CLOCK == 100
SiI680: 100% native mode on irq 17
ide0: BM-DMA at 0xbffed0-0xbffed7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xbffed8-0xbffedf, BIOS settings: hdc:pio, hdd:pio
hda: TS8GSSD25-S, ATA DISK drive
ide0 at 0xbffef8-0xbffeff,0xbffef6 on irq 17
hda: max request size: 64KiB
hda: 15924384 sectors (8153 MB) w/1KiB Cache, CHS=15798/16/63, UDMA(66)
hda: hda1 hda2 hda3
physmap platform flash device: 00400000 at ffc00000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 5 MTD partitions on "physmap-flash.0":
0x00000000-0x00300000 : "mtd_firmimg"
0x00300000-0x00370000 : "mtd_bootcode"
0x00370000-0x00380000 : "mtd_status"
0x00380000-0x00400000 : "mtd_conf"
0x00000000-0x00400000 : "mtd_allflash"
usbmon: debugfs is not available
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 19, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 19, io mem 0xbfffe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 19, io mem 0xbfffd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Adding console on ttyS0 at MMIO 0x80004600 (options '57600n8')
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 120k init
INIT: version 2.86 booting
Setting the system clock.
Activating swap...Adding 262576k swap on /dev/hda2. Priority:-1 extents:1 across:262576k
done.
EXT3 FS on hda1, internal journal
Setting the system clock.
Cleaning up ifupdown....
Loading kernel modules...done.
Checking file systems...fsck 1.41.3 (12-Oct-2008)
done.
Setting kernel variables (/etc/sysctl.conf)...done.
Mounting local filesystems...mount: /dev/hda4 is not a valid block device
failed.
Activating swapfile swap...done.
Setting up networking....
Configuring network interfaces...if-up.d/mountnfs[eth0]: waiting for interface lo before doing NFS mounts (warning).
done.
INIT: Entering runlevel: 2
Starting enhanced syslogd: rsyslogd.
Starting KURO-BOX event daemon: kuroevtd.
eth0: Setting full-duplex based on MII#1 link partner capability of cde1.
Starting internet superserver: inetd.
Starting periodic command scheduler: crond.
ttyS1 port init : AVR init string send.
Debian GNU/Linux 5.0 KURO-BOX ttyS0
KURO-BOX login: root /* root にログイン */
Password: /* 初期パスワードは「root」 */
Linux KURO-BOX 2.6.20-kurobox #2 Mon Feb 5 23:11:01 JST 2007 ppc
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
KURO-BOX:~#
KURO-BOX:/# uname -a /* カーネルのバージョン確認 */
Linux KURO-BOX 2.6.20-kurobox #2 Mon Feb 5 23:11:01 JST 2007 ppc GNU/Linux
KURO-BOX:/#
Return
2011/02/02